Indonesia API gate valve Body – machining

This lot valve export to indonesia  for end user :oil&gas company are machining:

The order include: 18pcs 12″ 150lb gate valve in A216 wcb Trim 5, 10 pcs 10″ API gate valve , 5 pcs 10″ swing check valve 150lb, 48 pcs 6″ 150lb wedge gate valve. 24 pcs 150lb swing check valve

Design standard:API600, Flange: ASME B16.5 Face to face: ASME B16.10, Inspeciton: API598 Delivery time: shipment in 50 days

Nov 20th, 2013

Válvula de balanço, API dupla flange Válvula de balanço, API flanged swing check valve

Nome do produto: Válvula de balanço (swing type check valve)

É geralmente apareceu com dupla flange da válvula de verificação do balanço, uma válvula de retenção tradicional, tem aplicação extremamente ampla. É simples e confiável, o que significa que a tecnologia é bastante maduro e estável, fácil de reparar. API válvula de swing e balanço DIN válvula adotar disco diferente pendurado estrutura.

Standard e escopo:

 Tamanho: NPS 2 “~ 36” DN50 ~ DN900
Avaliação da pressão: Classe 150 ~ 2500 PN2.5 ~ PN100
Conexão: face aumentado, Soldar, face Anel conjunta, face Masculino, Feminino rosto, solda de soquete e assim por diante
Material: aço carbono, aço inoxidável, liga e assim por diante
Projeto e Fabricação: ASME B16.34 e API 6D, BS EN 1868, DIN 3840
Inspeção e teste: API 598 ou API 6D, BS EN12569
Dimensão final flange: ASME B16.5 (NPS para ≤ 24); ASME B 16,47 série B (o nosso padrão normal), API 605 ou ASME B16.47 série A, MSS SP-44 (para NPS> 24; BS EN 1092 – 1
BW dimensão final: ASME B16.25
Soldadas-dimensão: ASME B16.11
De ponta a ponta: ASME B16.10, BS EN 558-1, DIN 3202, ISO 5752
TEMPERATURA E PRESSÃO: ASME B16.34
Dimensão da parede espessura: API 600 e BS 1868, API603 
Característica de projeto
Assento
Para o carbono válvula de retenção de aço swing, o assento é normalmente de aço forjado. A superfície de vedação da sede de pulverização é soldada com liga dura exigidas pelo cliente. Sede roscada renovável é usado para NPS ≤ 8 válvulas, e soldados no assento também pode ser opcional se a ser solicitado pelo cliente. Soldado no assento é usado para NPS ≥ 10 carbono válvulas de aço.

Para Válvula de aço inoxidável de verificação, assento integral é usualmente adotados, ou para soldar liga dura diretamente integralmente. Rosqueado ou soldada no lugar também é opcional para válvula de aço inoxidável de verificação, se necessário.

Corpo-a-Bonnet Conjunto: Junta
Aço inoxidável + de grafite flexível feridos é usado para Class150 e Class300 válvula de retenção; aço inoxidável + de grafite flexível feridos é usado para Class600 válvula de retenção, e junta conjunta também é opcional para Class600 válvula de retenção; junta anel comum é usado para Class900 válvula de retenção , projeto do selo de pressão é usado para Class1500 ~ Class2500 válvulas de retenção.

Conexão corpo e capota
O corpo ea capota de Class150 ~ Class900 válvulas de retenção são normalmente conectados com pregos e porcas. E o corpo e tampa de Class1500 ~ Class2500 válvulas de retenção são geralmente do projeto Selo de pressão.

Back to Manufacturer of Ball Valve,Gate Valve,Butterfly Valve,Check Valve,Special Valve, -China Sangong Flow Control

Check valve-Non-return valves:lift check valve,swing check valve,butterfly check valve,dual plate check vavle,tilting disc check valve

Check Valve
Check valves or Non-return valves (NRV) are normally installed in piping to avoid back flow. Rotating equipment such as pump, compressor, etc will always be equipped with NRV(s) on the discharge to avoid back flow when rotating equipment is shut. Back flow creates severe surging to the rotating equipment and potentially damage the equipment. In certain process system, NRV will be employed to avoid contamination, overheating, etc due to back flow.
Check valves or Non-return valves (NRV) -One way valve is basically an automatic valve open to allow forward flow and close to against reverse flow. In principle, it split into four basic types. There are swing, dual-plate, tilting disc and lifting type. Wrong selection of check valve type can leads to operability problem, leakage and continual maintenance issue.

Lift Check valves

– higher pressure drop is expected.
– equipped with small return spring to facilitate valve closure on reverse flow
– two type of seat. hard seat for for high differential pressure sealing and resilient seat for low differential pressure sealing
– shortest travel length. Fastest response.
– excellent performance for low and/or pulsating flows
– not good for fluid with particles
– Body install horizontal with disc / piston vertically
– Small check valve range from 1/2″ to 2″ lift piston type check valve
– Prefer operate in full open position
Minimum Recommended Line Velocity, Vmin (ft/s) = 12 SQRT (v)
where
v = Specific Volume of the Fluid (ft3/lb)

Swing Check Valve

– Tight sealing / shut-off
– Low pressure drop
– Susceptible to water hammer
– Not good for low flow and/or pulsating flow
– Vertical (upward flow) & horizontal installation
– Easiest check valve to maintain
– Prefer operate in full open position
Swing check valves should be sized such that the flow velocity in the line is sufficient to hold the disc in the fully open position.
Minimum Recommended Line Velocity, Vmin (ft/s) = 75 SQRT(v)
where
v = Specific Volume of the Fluid (ft3/lb)

Dual plate Check valve

The characteristic of dual plate check valve is pretty same as swing check valve.
– low pressure drop
– Not good for low flow and/or pulsating flow
– Vertical (upward flow) & horizontal installation
– Faster opening and closure compare to swing check valve
– Susceptible to water hammer (lesser than Swing check valve)
– Prefer operate in full open position

Tilting Disc Check Valves

– Fast opening and closing without damage to disc and seat
– Stable at low and pulsating flows
– Moderate pressure drop. Lower than lifting check valve but higher than swing check valve
– Vertical (upward) & horizontal installation
– Moderate tight sealing
– Prefer operate in full open position
Minimum Recommended Line Velocity, Vmin (ft/s) = 24 sqrt (v)
where
v = Specific Volume of the Fluid (ft3/lb)

Selection Consideration
There are four (4) main criteria shall be considered for the selection of check valve type :
non-slam characteristic
pressure loss
cost
application
Comparative rating for each type of check valve have been provided for these criteria (specifically first two technical criteria). These rating will be plotted on a Check Valve Comparative Selection Chart and together budget for final selection.